top of page
Planeprint-Dash-render1
Logo-Dash.jpg
slicing-P5
slicing 180x180x180 Bambu A1 mini and Prusa mini

DASH DLG

RC Discus Launch Glider designed by René Marschall

  • Wingspan: 1360 mm (53.5 inches)

  • Flight weight: 410 grams

  • Wingload: 18g/dm2

  • 4 channels

  • ​Material: LW-PLA 260g/PLA+ 50g/TPU 1g

  • Printer space of 180x180x180 mm (cube)

Planeprint DASH official pic
PLANEPRINT DASH in the air

PLANEPRINT DASH – The 3D-Printable Discus Launch Glider

 

The wish for a 3D-printable Discus Launch Glider (DLG) has been around for a long time. Honestly, we hesitated to take on this challenge for quite a while – combining the extreme structural loads of a discus launch with an ultra-lightweight airframe is notoriously difficult. There is a good reason why competition DLGs are built using complex carbon-molding processes and come with a hefty price tag.

​

With the PLANEPRINT DASH, we believe we have found the sweet spot: a well-balanced compromise that brings tons of fun to everyday RC pilots and serves as an ideal, affordable trainer to get into DLG flying.

After numerous prototypes and extensive test flights, we pinpointed the exact high-stress zones and refined the engineering to create a durable, everyday-ready glider.

 

Smart Structural Engineering

​

  • Lightweight, High-Precision Wing: Tensile and torsional forces along the wing are absorbed by two V-shaped carbon tubes bonded directly to the launch pin. This allows the wing itself to be printed from LW-PLA (or similar foaming filaments) with relatively low infill – keeping weight to an absolute minimum while maintaining high airfoil accuracy.

​

  • Bending-Stiff, Torsion-Flexible Fuselage: We deliberately decided against a standard carbon tube tailboom. Not only did we want to integrate the Bowden cables organically inside the fuselage, but standard off-the-shelf tubes aren't up to the task, and specialized filament-wound tubes are expensive and hard to source. Instead, the fuselage core is printed in LW-PLA with a diamond-shaped cross-section to counter lateral bending forces during launch. Four channels along the edges house thin carbon rods bonded over the entire length (similar to our SORATO or AERON). This unique combination of soft LW-PLA and high-tensile carbon creates a boom that is extremely stiff against bending, yet torsionally flexible – allowing the tail to twist up to ~15 degrees. While completely unnoticeable in normal flight, this flexibility absorbs massive peak loads and prevents structural failure.

​

  • Reinforced & Replaceable Horizontal Stabilizer: The outer horizontal stabilizer endures the highest loads during launch. To handle this, it is reinforced with three carbon rods and mounted with screws so it can be easily replaced if needed.

​

  • Hybrid Tail Surfaces: Tail weight is critical in a DLG – a fully 3D-printed tail would simply be too heavy and require too much nose ballast. Following the hybrid approach used in our GIPPSLAND and SWIFT S1, the tail surfaces are cut from lightweight foam board (or balsa wood, if you prefer). Flight testing proved that this drastically improves launch behavior, providing immediate directional stability without tail wagging.

 

Flight Performance & Handling

 

This hybrid construction achieves an all-up weight (AUW) of just 410 grams. While that won't win you a high-end F3K competition, the slightly wider wing chord gives the DASH fantastic flight characteristics, allowing it to sniff out and climb in even the slightest thermals.

​​

With this DLG, you can achieve good launch heights without much effort. Throwing the model too hard – as is common with competition models – doesn't damage the airframe, but it also doesn't get the model any higher; the limiting factor here is the soft tail surfaces.

​​​

Ready for Left- and Right-Handed Pilots

 

Even though 3D-printed parts can easily be mirrored in your slicer, we have included dedicated native STL files for left-handed pilots who prefer the launch pin on the right wingtip.

​

We are thrilled with how the PLANEPRINT DASH turned out: an accessible, budget-friendly, and easy-to-build DLG that delivers pure flying fun.

PLANEPRINT DASH blueprint
PLANEPRINT DASH 3D printing parts of the Plane

INNOVATIVE FEATURES OF OUR DASH

Download our free PRINTING & ASSEMBLING MANUAL, here you can see exactly what to expect before you decide to buy the STL data.

3d printing manual Planeprint DASH

PDF MANUAL DASH V1.0

We are constantly improving the manuals. Check if you have the latest version.

​​​

CHANGELOG

If you need Support please contact us only by email to info@planeprint.com with your order number or choose our Facebook group Planeprint Pilots.

  • m-facebookpicto
  • instapicto
  • Youtube
  • Tick Tack
  • m-facebookpicto
  • instapicto
  • Youtube
  • Tick Tack

© 2025/2026 – All rights reserved by PLANEPRINT Marschall e.U. – Innsbruck Austria • mail

Fair data use

Affiliate Disclaimer: We use affiliate links to support our website. This means that if you click on a link and make a purchase, we may earn a small commission at no extra cost to you. We only recommend products we believe in and personally use. Thank you very much for your support!

bottom of page